![]() Here is an example of a set I made with the tables and without pocket hole screws. I hope you can make this project, with or without the tables. You can add spacing if you like but I have never had a problem without a spacing. If you followed the pocket hole schedule you will use two pocket hole screws in each slat. Lay your slats out with a good side facing down and attach your frame to the slats. It will be impossible to get a drill in here if you start with the long sides.Ĭonnect both short sides by attaching the longer sides. Next, drill all of your pocket holes according to the included diagram.Īssemble the short side of the table first. To make the legs you will have to make two rip cuts with either a table saw or a circular saw. 24 2-1/2″ pocket hole screws (Kreg Blue-Kote)Ĭut all of your pieces according to the cutting diagram.You will need to use a pocket hole jig for this table. In the video, I only built a bench but here I want to include the instructions to build a couple of side tables as well. I think it just flows a little better this way. Then I use the pencil again to space the rest of the back slats. I use a permanent marker for my first spacing here (about 1/2″). However, I always increase the spacing between the seat and the first back slat just slightly. ![]() If you don’t have one handy, the gap is 1/4″ between slats. I designed this bench so that you could use a standard wood pencil as a spacer in between slats. The rest of the seat slats are secured the same way. I had to lift the leg assembly slightly and use a 6″ extension for my drill to be able to screw it down. If you are using pocket hole screws like me this first slat will be a little tricky to secure. Push it all the way against the back supports and attach it with glue and screws. Make sure the good side is visible on all of your slats. I always attach the back seat slat first. If you used pocket holes make sure you position the board so that the pocket holes are in the back. If you did not use pocket holes you can use two 2-1/2″ outdoor screws to attach directly into the lower part of the back supports. This piece connects both leg assemblies together. ![]() Then finish securing the second back support. This way I can place them on the ground and make a slight adjustment if needed. I always secure one all the way and start with one screw on the second assembly. It is also important to make sure these are attached at the same angle. Each overlapping parallelogram gets glue and two screws along the long diagonal. Make sure that you do not overlap any pocket hole locations and that all of the pocket holes face the inside of the bench. Next, attach the back supports so that they intersect the top corner of the leg assembly and are flush with the bottom of the lower horizontal leg member. Use another piece of 2×4 as a spacer to locate the lower horizontal member (23-3/4″). Use glue and two 2-1/2″ screws at every joint. Be sure to put your 2-1/2″ outdoor screws along the long diagonal of this parallelogram as shown with this small image to the left (disregard the colors of this image). When these pieces intersect they form a parallelogram. Start with securing the 20″ piece to both legs first. The legs are assembled with the horizontal members on top. You can skip this step if are going to secure the slats from above with screws. Remember to flip the cuts for the left and right pieces so you don’t end up with two left legs. You can locate the pocket holes using the included diagram. To further reduce the appearance of screw heads we can cut pocket holes with a Kreg Jig on the upper horizontal leg pieces (20″) and the back supports (31″). We will be building from the inside out to minimize the appearance of screw heads. With all the pieces cut, arrange them so that the good side is down. You can make every cut with either a hand saw, circular saw, or in my case a miter saw. The first step is to cut all of your pieces according to the materials list. zip file containing the SketchUp file for this bench. I have included a picture near the end of this article to show you the bench without pocket holes.Ĭlick here to download a. The slats can simply be screwed down from the top as well. Don’t worry if you do not have a pocket hole jig. The bench utilizes pocket holes to secure the slats with no visible screw heads. The tables are pretty self-explanatory and I had no need for them at the moment so I did not include them in the video build. However, in the video tutorial, I will only be building the bench. In this tutorial, I will show you how to build a bench and a couple of side tables.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |